About Focal Point

Focal Point architectural products are manufactured using a closed cell polymer, with the density and workability of white pine. These products can be used for interior or exterior application with no special preparation because they are factory-primed. Not only are the products ready to install, but they are virtually maintenance-free.

For over 30 years Focal Point has been skillfully blending old world craftsmanship with 21st Century technology to achieve the highest level of detail and quality. This process allows us to offer you crown mouldings that not only enhance the elegance of any room, but offer a piece of history.

NEW Focal Point Dome with Light Cove 98521 $2,501.13

Dimensions
Depth Interior: 15 1/2"
Width: 78"
Inside Width: 71"
Rough Opening: 75 1/2"
Rough Opening Depth: 15 1/2"

Dome may be used with any Medallion 20" in width or less, sold separately >

Dome requires approximately 19’ of U.L. approved rope lighting, (not included). Lighting is not provided by Focal Point. The rope lighting can be overlapped or doubled up for increased illumination dependent upon manufactures specifications. Clear rope will give a candle light colored glow to the dome. For best effect use a rheostat (dimmer) on the wall switch.

Find out more about NSL Rope Lighting >

Supplied Materials 1- Dome, 4- Z-bars, 12- 1/4" nuts, 8- Washers for 1/4" threaded rods, 8- Panhead Phillips wood screws, 4- 6"x1/4" threaded bolts

Focal Point Heritage-Henredon Contemporary Moulding 19540

19540 Heritage-Henredon Crown $227.84

Dimensions
Height: 5 3/4"
Length: 12'
Projection: 4 1/4"

Focal Point Acropolis Crown Moulding 23125 $29.17

Dimensions
Height: 3 1/8"
Length: 8'
Projection: 2 1/2"

Focal Point Athenian Leaves Crown Moulding 23145

23145 Athenian Leaves Crown - 4 1/8" $29.17

Dimensions
Height: 2 5/8"
Length: 8'
Projection: 2 5/8"

Focal Point D`Evereux Crown Moulding 13070

13070 D`Evereux Cornice - 12 ft $131.23

Dimensions
Height: 4 3/4"
Length: 12'
Projection: 4"

Focal Point Egg & Dart Crown Moulding

Focal Point Versailles Crown Molding 10750

10750-8 Versailles (Z40) - 8 ft $98.50

Dimensions
Height: 6 7/8"
Length: 6 1/2'
Projection: 7"

Focal Point Versailles Crown Center Piece 10760

10760-8 Versailles Center Pc. (Z41) - 8 ft $114.51

Dimensions
Height: 6 7/8"
Length: 6 1/2'
Projection: 7"

Focal Point Versailles Inside Corners 10770

10770-8 Versailles Inside Corners (1 set makes 4 corners) $252.41

Dimensions
Length: 6 1/2'

Focal Point Versailles Frieze 25230

25230 Versailles Frieze $29.14

Dimensions
Height: 4 7/8"
Length: 8'
Projection: 5/8"
Repeat: 11 1/4"

Focal Point Versailles Ceiling Medallion 81033 $116.88

Dimensions
Canopy: 3 1/4"
Width: 32 1/2"
Hole: 4"

Focal Point David Wright House Crown Molding

19500 David Wright House Crown $188.08

Dimensions
Height: 7 3/4"
Length: 12'
Projection: 3"

Focal Point Dauphine Crown Molding 10580

10580-8 Dauphine (Z9) - 8 ft $38.15

Dimensions
Height: 3"
Projection: 1 3/8"

Focal Point Adefix

Adhesive for covings, framings and ceiling centers

33324

Adhesive3

Case of 24 tubes

$143.69

33333

Adhesive3

Single Tube

$6.26

34424

P5 Nomastyle Adhesive

Case of 24 tubes

$103.09

34444

P5 Nomastyle Adhesive

Single Tube

$4.94

34445

P5 Nomastyle Adhesive

1 Kg Pail

$7.01

34446

P5 Nomastyle Adhesive

5Kg Pail

$24.55

1. Cutting

• Mark Projection and depth on walls and ceilings. These dimensions can be found in the chart on the back of this sheet.

• Cut 45° compound miters for inside and outside corners (do not cope inside corners). Apply Focal Point Adhesive #33333 and fasten with trim screws or finish nails.

• Cut butt joints for all straight joints, apply AD3 Adhesive to both edges. (do not use scarf or lap joints).

• For large profiles (8" face or larger) apply 1/4" bead of AD3 Adhesive #33333 to the top and bottom bedding edges on the back side of moulding (see figure 1) or apply AD3 Adhesive #33333 to inside wall and ceiling marks.

• Cut mouldings 1/4" longer and spring into place. If necessary, screw a wooden block to the wall and spring moulding against the block. Screw or nail moulding into place then remove the block (see Figure 2).

• Screw or nail moulding every 16".

• Remove excess wet adhesive with mineral spirits.

2. finishing

• Caulk mouldings to wall and ceiling using a paintable latex caulk.

• Fill screw or nail holes with vinyl spackle.

• Cover joints with vinyl spackle and lightly sand with fine grit paper.

• If factory primer is sanded off, apply vinyl spackle to area, lightly sand, and prime.

• Use a high-quality latex or oil-based paint.

• Do NOT use lacquer paints.